Request An Appointment

 

 

What're your thoughts about Tools You Need to Install a New Bathtub ?

Installing a bathtub isn't precisely brain surgery, but it does require solid plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately difficult project. If the old bathtub is conveniently obtainable, the task can relocate speedily; if you have to open a wall surface to eliminate the old bathtub and also position the new bathtub, the task is a lot harder. In either instance, the task is within a residence handyman's skills, although you will need a helper to leave the old bathtub and set in the new one. Make certain you have actually certified on your own for the work and also are comfortable attempting it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider utilizing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This post will certainly assist you install a new bathtub in your restroom if you have already purchased a new tub and don't require to transform the setup of your previous water pipelines.
Your devices and also product list ought to make up the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Preparing for the Installment

First of all, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the versatile faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.

 

 

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic because of the limited gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will originate from the pipelines. Once the supply pipelines have actually been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.

 

 

Installing the Tub

Making use of both wooden boards under its feet, place the tub in the called for placement. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub up until the level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water supply and check all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the tub as well as likewise inspect the overflow electrical outlet and also the regular outlet for leaks.
Lastly, take care of the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub needs to wait till the tub has actually been utilized a minimum of when as this will settle it right into its final position.

 

 

Fitting New Taps

If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the tap in position with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous type should be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bathtub

In the location where the bath meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface in between the bath and also the tiling, resulting in difficulties with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components as well as installations. They are offered in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealer can crack relatively early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.

 

How to Install a Freestanding Bathtub?

 

Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.

This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.

 

Slope

 

Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.

 

Placement

 

A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.

According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.

 

Clean the bathroom floor

 

After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.

 

Steps to Install a Freestanding Bathtub:

 

STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.

STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.

STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.

STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.

STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.

STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.

 

Tips to Maintain a Freestanding Bathtub:

 

• Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.


 
• Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.


 
• Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.


 
• Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.


 
• Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.


 
• If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

 

https://www.magnushomeproducts.com/blogs/inspired-living/how-to-install-a-freestanding-bathtub-a-diy-method-with-6-steps

 

I recently found that blog post on Tools You Need to Install a New Bathtub while doing a search on the internet. Sharing is good. You just don't know, you may very well be doing someone a favor. We truly appreciate reading our article about How to Install a Bathtub.

Book A Service Call